“Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***”
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please
contact your local dealership to see if your vehicle requires dealer programming.
1. Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turnignition to OFF and remove key.
2. Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Waitapproximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn
ignition OFF and remove the key.
3. Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
4. For each additional key you must repeat these steps starting with step number 1.
Call (877) 782-5192 for a local Locksmith
Instructions
How to Program a 2006 Jeep Commander Keyless Entry Remote Fob Smart Key
Step by Step How to Programming Instructions:
Note: You must have two programmed keys to add a new key to the system.
1. Insert the first valid key into the ignition switch. Turn the ignition switch to the ON/RUN position for at least three seconds, but no longer than 15 seconds. Then, Turn the ignition switch to the LOCK position and remove the first key.
2. Insert the second valid key into the ignition switch. Turn the ignition switch to the ON/RUN position within 15 seconds. After 10 seconds, a chime will sound. In addition, the Vehicle Security Light will begin to flash. Turn the ignition switch to the LOCK position and remove the second key.
3. Insert the new key into the ignition switch. Turn the ignition switch to the ON/RUN position. within 60 seconds. After 10 seconds, a single chime will sound. In addition, the Vehicle Security Light will stop flashing. To indicate that programming is complete, the Vehicle Security Light will turn on again for seconds and then turn off.
The new key is now programmed.
The Remote Keyless Entry transmitter will also be programmed during this procedure.
Repeat this procedure to program up to eight keys.
to find a Locksmith in your area.
We strive to provide convenience to our customers with free keyless entry remote fob programming instructions for every single vehicle that we sell on NorthCoast Keyless. Many people don’t know that they can purchase their own replacement vehicle entry remote, save up to
70% off of marked up Dealership prices, and program the replacement remote to their vehicle themselves. We know how good it feels to save money and do something yourself; and we aim to make it as painless as possible for you! Time needed: 5 minutes. Easy to Follow Step-by-step Key fob remote Programming Instructions
Free Key Fob Remote Programming Instructions for a 2006 Jeep Commander
REMOTE HEAD KEY FOB
Step-By-Step How To Programming Instructions
- Insert First Programmed Key
INSERT a working remote head key into the Ignition and TURN it to the ON/RUN position.
- Remove First Programmed Key
WITHIN 3-15 seconds, TURN the Ignition back to the OFF/LOCK position and REMOVE the key.
- Insert Second Programmed Key
INSERT a second working remote head key into the Ignition and TURN it to the ON/RUN position. After 10 seconds, the vehicle will chime to indicate successful entry into Programming Mode.
- Remove Second Programmed Key
TURN the second working remote head key to the OFF/LOCK position and REMOVE it from the Ignition.
- Program Remote
INSERT the NEW remote head key into the Ignition and TURN it to the ON/RUN position. After 10 seconds, the vehicle security light will STOP flashing. It will FLASH again to indicate successful programming of this remote head key.
- Program Additional Remote
REPEAT Step 5 to program any additional remotes to your vehicle.
- Exit Programming Mode
TURN Ignition to OFF/LOCK and REMOVE key to EXIT Programming Mode.
- Test Remotes
TEST all remotes. Programming is complete.
- Share
If these programming instructions helped save you time and money, please consider sharing our website with friends and family so they can do the same.
Programming Notes:
- Verify the following prior to following these instructions:
- Your vehicle is equipped with keyless entry, and
- You have a key fob remote that is compatible with your vehicle.
- Obtain ALL remote transmitters for this vehicle.
- You MUST have at least TWO working remote head keys in order for this procedure to work.
- If you don’t have at least TWO working remote head keys, you MUST have the remote programmed by an Automotive Locksmith.
If you have any difficulties with programming your vehicles, contact us at [email protected].
Key fob remotes
2006 Jeep Commander
MONEY BACK GUARANTEE
We offer a No Questions Asked Money Back Guarantee on all of our products!If you can’t get it to work for your vehicle–reach out!We’ll get you your money back.
FAST & FREE SHIPPING
ALWAYS! First Class USPS shipping is always shipped for free for all Domestic (US) customers in less than ONE business day. No ifs, ands, or buts!
CUSTOMER SUPPORT
Have a question for us? Reach out! We're here for you. We will work with you to solve your issue rather than just having you return an item without a solution like some of the big box online stores do.
SAVE 70% OVER DEALERSHIPS
We’ve worked hard to create a network of reliable and reasonably priced suppliers that allow us to give you rock bottom prices.You're also not paying for huge fancy offices or sports cars for our Owners. We always will be just regular people tryin’ to make a livin’ not a killin’!
NorthCoast Keyless Free Programming Instructions Disclaimer:
- We worked hard to provide these instructions to our customers. We checked multiple sources to ensure that this information is complete and accurate. However, please understand that we cannot be held liable for any loss due to incorrect use of the programming instructions from www.northcoastkeyless.com.
- If you cannot program your remote with the instructions that we provide or encounter any discrepancies, please contact us at [email protected] and we’ll make sure that you’re taken care of.