PLEASE PATRONIZE OUR SPONSORS!
If you would like to help maintain this site & enhance it, feel free to donate whatever amount you would like to!
| |||
hey everyone |
| ||||
There's not much to mess up on a fluid and filter change. 2) Remove cover and drain fluid. Also remove debris or
gunk at the bottom of inside housing. Remove filter. __________________ |
| |||
The tech section will have the service manual for you if you need a step by step but as already posted it's pretty easy. |
| |||
thanks, going to change it the week |
| ||||
Just a hint, before removing the filter be sure to clean off all the junk on it, to get the top I usually loop a rag over the top of the filter and pull back and forth to loosen the dirt, getting back near the sealing area a much as possible, then blow it off with air. __________________ |
| |||
I just changed the hydro fluid in my 1710. Is there a better way to fill it than to put it in through the dipstick tube? I took me about 2 hours with all the burping. I had a piece of copper tubing stuck down i to let out the air but that didn't help much. The fluid is just too thick. I actually had the filter cross threaded. It seemed to go on normally but leaked. I took the tunnel cover off then i could see it wasn't straight. I'm glad I did it though, the oil didn't look dirty by it sounds a lot better! I bought her last year she's got 780 hours. Nice machine! |
| ||||
Quote: Originally Posted by berks1710
I just changed the hydro fluid in my 1710. Is there a better way to fill it than to put it in through the dipstick tube? I took me about 2 hours with all the burping. I had a piece of copper tubing stuck down i to let out the air but that didn't help much. The fluid is just too thick. I actually had the filter cross threaded. It seemed to go on normally but leaked. I took the tunnel cover off then i could see it wasn't straight. I'm glad I did it though, the oil didn't look dirty by it sounds a lot better! I bought her last year she's got 780 hours. Nice machine! The only other way would be to remove the fender pan and the top cover and dump it in that way. |
| ||||
Quote: Is there a better way to fill it than to put it in through the dipstick tube Two suggestions.. (A) Insert a small piece of plastic tubing (1/8" to 1/4: Dia) into the filler tube. Pour the hydro fluid out side of the plastic tube and into the filler tube. The plastic tubing serves as a air release. (B) Drill and tap a hole in the rear cover above the normal fill level. I used a 7/16" Fine Threaded Flange bolt with a matching Rubber Washer to plug this hole. Remove the bolt to fill, once filled, install the bolt into the rear cover and away you go. This bolt serves as a air release also. __________________ CC Models: 100, 105, 129, 1450, & 784 Buy: Made in the USA |
| ||||
put yur jug of fluid in front of a heater for a while. flows a little quicker when its warmed up. __________________ |
| ||||
Quote: Originally Posted by cmatthew put yur jug of fluid in front of a heater for a while. flows a little quicker when its warmed up. Another option. NIK, __________________ |
| Forum Jump |
All times are GMT -4. The time now is 12:25 AM.
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2022, vBulletin Solutions Inc.
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: //www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.