Enter the characters you see belowSorry, we just need to make sure you're not a robot. For best results, please make sure your browser is accepting cookies. Show
Type the characters you see in this image:Try different image Conditions of Use Privacy Policy © 1996-2014, Amazon.com, Inc. or its affiliates Below is information to help you program your Garage Door Operator remote control or outside keypad. If you need additional help, please reach out to the manufacturer directly, as we are a local Louisville garage door company. Please refer to our garage door services to learn more about the services we offer and how we can help home and business owners in the Louisville, Elizabethtown, and Lexington, KY areas. LIFTMASTER MYQ APP If you’re trying to program your smartphone to operate your garage door remotely, please see our blog, How to Set Up MyQ App for complete instructions and a video tutorial. Programming 971LM and 973LM, 371LM and 373LM Security Plus Transmitters
976LM, 377LM Security Plus, and 66LM Wireless Keyless Entry Systems
The square smart button is located on the side or the back of the motorhead, and is colored red, green, amber, orange, or purple. It is directly under the #1 wire terminal screw. Programming Instructions for Genie Remotes:
** To erase all Intellicode remotes and wireless keyless entry, hold down on the learn button until the indicator light stops blinking, then proceed to Step 2. Programming Genie Digital Remote Transmitters with Internal Set SwitchesThese transmitters work by matching the settings on the internal code setting switches with the same set of switches in the receiver on the garage ceiling. The receiver is located either behind the light lens of the Genie garage door opener motorhead, or inside an external small rectangular box on the ceiling, which is connected to the motor head by a set of wires. Note: the frequency of the transmitter must be the same frequency as the receiver on the ceiling for it to work. Genie has been making the 390 MHz frequency exclusively for the last 15 years. Programming Genie Multi-Button Digital Remotes with Internal Set SwitchesThese garage door opener transmitters have 2 smaller switches to the right of the internal Code Setting Switches. The small right switch should be set according to how many Code Setting Switches in your receiver (either 9 or 12). The small left switch is for programming purposes. To program a button for one of your doors, follow the instructions below:
Genie Garage Door Opener KeypadsGenie Garage Door Opener Wireless Keypad Model GPWK-12,
GWK Step-By-Step Programming Procedure
This keyless garage door opener entry pad works with Genie transmitters using 390 MHz frequency. It is NOT compatible with Genie Intellicode transmitters (if your keypad has Intellicode printed on the cover, go to the next set of programming instructions below). The Door Code in the Step-By-Step Procedure at right is determined by the internal code switches inside your transmitter and the accompanying chart. Determine the settings of the first 3 switches and write down the corresponding number from the chart. Continue with the next 3 switches and its corresponding number, and so on, until the last set of 3 switches. You should have 3 or 4 Door Code numbers.
Door Code in Step #4: ____ ____ ____ ____ Genie Wireless Intellicode Keyless Entry Pad Programming2 Models GWKIC, ACSDG, Two-Part, Step-By-Step Programming Part 1:
To Program the Intellicode Wireless Keypad
NOTE: If the red indicator light does not blink, it is not taking the programming steps. Check the 9-volt battery under the keypad numbers. To access, press inward, under the number pad lip while sliding down to expose the battery. Part
2:
Adding More Doors to Keypad:
With most Genie units, remove the light lens globe to expose the Learn Button on the motorhead. The learn button is sometimes located on the back of the unit, or with Accelerator openers, it is under the light lens near the hinge of the lens globe. Always locate the floppy antenna wire first. The Learn Button can be found not far from this antenna. See Troubleshooting Guides for Accelerator photo. Intellicode Model GWKP (off-white with flip-up cover) Programming Instructions for the GWKP Genie garage door opener keyless entry involves following the two sets of steps below:
Find the Learn Code Button and the LED indicator light on your Genie motor head inside the garage. It is usually behind the light lens and close to the floppy antenna wire. If your Door Opener does not have an antenna, you have an External Receiver. The External Receiver cover must be removed to access the Learn Code button and the indicator LED. Follow Steps 1 through 3 outlined below:
Multiple Genie Garage Door Opener Programming for GWKP- All garage doors will use the same PIN:
Homelink Garage Door Opener ProgrammingHOMELINK IN-CAR REMOTE PROGRAMMING INSTRUCTIONS To program a built-in-car transmitter to a rolling code garage door opener (Genie rolling code is called Intellicode, Liftmaster/Sears is called Security plus), you should take the following steps.
Programming a Fixed-Code Device (Majority of units made prior to 1996) These devices have internal dip-switches located near the battery of your remote.
UNIVERSAL HOME REMOTE FOR HOMELINK (UHR)Programming a Rolling Code Garage Door Opener If your in-car (UHR) remote has 3 LED lights, one above each button, you should follow the instructions below to program your Rolling Code Garage Door Opener.
Programming a Fixed Code Device (Majority of units made prior to 1996) Below is a picture of a typical 12-switch DIP switch layout located on your hand-held remote control under the battery cover (your remote may have 8-12 DIP switches). Note: Genie, Linear, Multi-Code and Stanley have only 2 position switches: up or down.
Programming of the Fixed Code device is now complete. Do Chamberlain remotes work with Craftsman?*Craftsman, LiftMaster, Do-It®, Master Mechanic®, Raynor® and True Value® are compatible with Chamberlain technology.
How do I connect my Craftsman garage door opener to my Chamberlain?CHAMBERLAIN / LIFTMASTER / SEARS CRAFTSMAN GARAGE DOOR OPENERS. Press and release the “smart” button on the garage door opener motor unit. The smart indicator light will glow steadily for 30 seconds. ... . Within 30 seconds, press and hold the button on the hand-held remote.. Release the button when the motor unit light blinks.. Are Chamberlain and Craftsman garage door openers the same?That's right, the Craftsman garage door openers are private-label devices made by Chamberlain and sold by Sears under its own Craftsman brand name. Since Chamberlain and Sears Craftsman garage door openers are produced by the same company, it stands to reason that these product lines would have numerous similarities.
|