2022 ram 1500 5.7 oil filter number

Hello all,
I am getting ready to do my first oil change on my 2021 Ram 1500. After looking around I see the oil filter part number varies. What is the right Mopar part number for the 5.7 Hemi? I assume the filter has changed throughout the years possibly why so many different numbers.

The part is MO-339.

Here is my thread on my first oil change, check out my notes, I think it will be really helpful with your first oil change, especially with the notoriously hard to remove first oil filter.

The part is MO-339.

Here is my thread on my first oil change, check out my notes, I think it will be really helpful with your first oil change, especially with the notoriously hard to remove first oil filter.

Thanks, that is the part number I was using but when I search with it I get several part numbers for example.

4892339AA​

4892339AC​

I think I even saw an AB as well.

Thanks, that is the part number I was using but when I search with it I get several part numbers for example.

4892339AA​

4892339AC​

I think I even saw an AB as well.

Yup, don't worry about that, just get the primary part number, MO-339. The one I got at Walmart for $10 had the exact same sub-partnumber as the one I took off. Though it shouldn't matter regardless.

The first oil change has been difficult for many because the filter is screwed on tight with limited access. I don't know if that has changed with the later produced Rams. I opted to have the dealer do my first oil change to avoid any potential problems/headaches.

The first oil change has been difficult for many because the filter is screwed on tight with limited access. I don't know if that has changed with the later produced Rams. I opted to have the dealer do my first oil change to avoid any potential problems/headaches.

It comes off easy if you get it up to temp, I helped a couple of locals doing their first oil change, they all came off easy if you get the oil temp around 200F. Which I believe you should do anyways before any oil change to get the most oil out.

If you do it cold, the original filter will be hard to remove.

It comes off easy if you get it up to temp, I helped a couple of locals doing their first oil change, they all came off easy if you get the oil temp around 200F. Which I believe you should do anyways before any oil change to get the most oil out.

If you do it cold, the original filter will be hard to remove.

So I know you say get it up to temp to remove the filter but is the oil too hot that it would melt the ziploc bag?

Thanks, that is the part number I was using but when I search with it I get several part numbers for example.

4892339AA​

4892339AC​

I think I even saw an AB as well.

I just got two last week. MO-339, 4892339AB.

I just got two last week. MO-339, 4892339AB.

I ordered one from Amazon yesterday. Let's see which one shows up.

So I know you say get it up to temp to remove the filter but is the oil too hot that it would melt the ziploc bag?

Nope, just try to get your temp at around 200F before you start your oil change. By the time you get to the filter, the oil will be around 180F or so, which is below the bags melting point.

If you get to say 220F after shutdown, then maybe wait 15 minutes or so before you begin your change.

I just got two last week. MO-339, 4892339AB.

You got the right one. I verified the part number with the dealer parts guy. He assured me the 4892339AB is the one you want.

What oil wrench worked well with removing the Mopar filter? Do the end cap filter remover work better?

What oil wrench worked well with removing the Mopar filter? Do the end cap filter remover work better?

I would expect the end cap type to work best. I reach in from the front and crank it by hand.

See post 45 and 46, worked for me. I currently tightened the filter 3/4 -1 after contact and have been able to remove the filter without any difficulty. I reach from front of vehicle in addition from underneath and get 2 hands on the filter.

Oil Leak??

Cripes, what a bunch of work for a nuisance noise. Good tech. Reminds me of an old 2nd hand story, back in 1973 I had a neighbor who always wanted a black 4 dr Sedan De Ville, circa 1967-69. He found one from the original owner. The older guy told him that for a few months after purchase he...

Additional reading FYI

Did my first oil change....

....and man, that oil filter was on tight!!! I have always hand tightened it such that I can easily spin it off the next time, with no tool needed. But this one absolutely required a filter wrench, and even then was pretty tough to move. Unreal.

1st oil change was a PITA!

I never use a wrench, my filters all break loose by hand. when installing new one: drop or so of clean oil on filter gasket face, screw on until gasket touches the engine, then tighten 1full turn by hand and STOP. Never, ever had a filter loosen after this; and ive always done my/our oil...

When are you doing your first oil change?

I just did my first oil change today at 3,500 miles. Wanted to do it a bit earlier but didn't get around to it. Agree with others that the filter location is terrible. For future changes I installed a Fumoto Valve to prevent the oil from draining onto the crossbar. Quick question. Is the...

Experiences with oil changes so far?

Hey guys, just wondering how your experiences have been with changing oil so far. Are you getting back 7 quarts when you drain your old oil? Do you end up having to put in less than 7 quarts based on your oil dipstick reading? What is your preferred oil type and brand? Are MOPAR filters the best...

Oil Change Intervals

Just curious at what interval everyone changes the oil in their 5.7 HEMI. I know that there may be exceptions based on trips coming up and weather etc. so please try to answer to what you would do for a regular change. If you change yours based on the indicator and track your miles, please...

Fumoto Oil Drain Valve

I have a 2020 Ram 1500 Laramie Longhorn and want to install one of these drain valves when I hit 5000 miles. Have any of you installed one in your 5th gen and if so what is the part number? They don't have anything newer than 2017 for Ram on their website.

First oil change, dealer pricing.

My dealer offers this. I've been having my oil changed there for 5 years. With my '15 I purchased 10 changer/rotations for 459.00....that's $45/change. WHen I purchased my 2020 they said that they were loosing their shirt on the oil changes and this was the best they could do, which still...

Hole on oil filter. What a mess.

So my truck was sitting for about two weeks and I turned it on today and did a few errands and when I got back there was a puddle of oil. I checked under the chassis and there was oil everywhere! It made it all the to my rear shock! I was trying to pinpoint where it was coming from since the oil...

Part number for MOPAR oil filter

Hello all, I am getting ready to do my first oil change on my 2021 Ram 1500. After looking around I see the oil filter part number varies. What is the right Mopar part number for the 5.7 Hemi? I assume the filter has changed throughout the years possibly why so many different numbers.

What oil wrench worked well with removing the Mopar filter? Do the end cap filter remover work better?

I’ve used one of these for years on all our family Rams and it works well.

This worked perfectly (after you get the truck up to temp)....

This worked perfectly (after you get the truck up to temp)....

I purchased one just this afternoon but noticed the size for the one in the link above has a 2.875 to 3.25 (73 to 82.5 mm) range. The one I bought is the Lisle as well https://shop.advanceautoparts.com/p/lisle-swivel-gripper-57030/10550413-P but shows 3.5 - 3.875 (88.9 - 98.4mm) Range. Fits most popular 3.625" standard filters.
Did I get the wrong size wrench or will this work? I am waiting for the new filter to arrive if not I have to crawl underneath and test fit the wrench.

I’ve used this type on every car and motorcycle I’ve owned.

Sent from my iPad using Tapatalk

I purchased one just this afternoon but noticed the size for the one in the link above has a 2.875 to 3.25 (73 to 82.5 mm) range. The one I bought is the Lisle as well https://shop.advanceautoparts.com/p/lisle-swivel-gripper-57030/10550413-P but shows 3.5 - 3.875 (88.9 - 98.4mm) Range. Fits most popular 3.625" standard filters.
Did I get the wrong size wrench or will this work? I am waiting for the new filter to arrive if not I have to crawl underneath and test fit the wrench.

I bought 4 different wrenches for my first oil change to make sure I got the right one, including the larger Lisle wrench which was too big. The smaller one is perfect, it's a smaller filter than you think, especially if you are use to the larger Motorcraft or Mopar filters that come on 4.0L Jeeps.